07-04-2024, 07:40 AM
(This post was last modified: 07-04-2024, 07:42 AM by harleymark54@gmail.com.)
I have a 1970 T2 van that has been lowered in the front using the beam lowering kit. Would anyone have a tip on the raise it back up?
Raising Front End that Has Been Lowered
|
07-04-2024, 07:40 AM
(This post was last modified: 07-04-2024, 07:42 AM by harleymark54@gmail.com.)
I have a 1970 T2 van that has been lowered in the front using the beam lowering kit. Would anyone have a tip on the raise it back up?
07-04-2024, 09:41 AM
Depends.
If it is an adjustable beam should just be a matter of adjusting back the other way. Then there is one off method where is is set. Also need to see if they have cut and rewelded the beam. Post up some pics of the centre of your beam if not sure
76 Bay Microbus - Woody
90 T3 Caravelle C Auto - Daisy
Adjustable
https://www.heritagepartscentre.com/au/a...TVEALw_wcB Weld in https://www.heritagepartscentre.com/au/a...B7EALw_wcB
76 Bay Microbus - Woody
90 T3 Caravelle C Auto - Daisy
07-04-2024, 10:56 AM
We installed adjusters a long time ago. Tried to adjust up {also a long time ago} and I could not shift it.
Alpal
Living the Dream. JFDI 1979 Bay Schmetterling
07-04-2024, 12:03 PM
T3’s and strut beetles are so much easier to play with.
76 Bay Microbus - Woody
90 T3 Caravelle C Auto - Daisy
07-04-2024, 12:10 PM
If it's been dropped on an adjustable beam / spindles, you'll need to raise the vehicle on a hoist in order to take all the weight of the spindles.
Should then be a matter of undoing the lock bolt and adjusting the height....carefully....the wheel and hub will move via gravity ..... If it's on a dropped, fixed beam.....you'll need to replace the beam itself to get it back up to stock.
Cheers,
Mark It’s not oil, it’s sweat from all the horsepower ! Pit crew for : The Tardis - a ‘76 Sopru Campmobile & Herman - the ‘71 White Low Light
07-04-2024, 02:45 PM
(07-04-2024, 12:10 PM)Oldman Wrote: If it's been dropped on an adjustable beam / spindles, you'll need to raise the vehicle on a hoist in order to take all the weight of the spindles. Good theory with adjusters. Even tried a BIG hammer and could not get it to move a shmidgeon!
Alpal
Living the Dream. JFDI 1979 Bay Schmetterling
22-04-2024, 11:49 PM
(07-04-2024, 09:41 AM)Barry Wrote: Depends. Hello Barry, see attached photo of the adjusters.
23-04-2024, 12:22 AM
(07-04-2024, 09:41 AM)Barry Wrote: Depends. Hello Barry, see attached photo of the adjusters.
23-04-2024, 08:33 AM
(23-04-2024, 12:22 AM)harleymark54@gmail.com Wrote: Hello Barry, see attached photo of the adjusters. As per Oldman's comments above Have a look here - beetle but same story. https://www.youtube.com/watch?v=JgLbQnqv0Fc I have not actually done it - but those adjusters seem to be at maximum up?? Maybe you have dropped spindles as well?
76 Bay Microbus - Woody
90 T3 Caravelle C Auto - Daisy |
« Next Oldest | Next Newest »
|